Published by on February 28, 2020
Categories: Literature

LMN/NOPB Texas Instruments Audio Amplifiers 5-W AUDIO POWER AMP datasheet, inventory, & pricing. LMN Datasheet, LMN National Semiconductor 5-Watt Audio Amplifier Datasheet, buy LMN. The LM is a power audio amplifier for consumer applica- tion In order to hold system cost to a minimum gain is internally fixed at 34 dB A unique input stage.

Author: Dourisar Mugor
Country: Montenegro
Language: English (Spanish)
Genre: Video
Published (Last): 2 June 2011
Pages: 176
PDF File Size: 1.42 Mb
ePub File Size: 4.44 Mb
ISBN: 141-2-90963-529-3
Downloads: 31117
Price: Free* [*Free Regsitration Required]
Uploader: Shaktisida

It’s worth mentioning that the above circuit can be simulated and will give the expected results, but datashest need to replace the upper NPN output transistor Q7 with a Darlington pair or you will not get symmetrical clipping. A unique input stage allows ground referenced input signals. If these pins are linked by a 10uF capacitor, the gain is 46dB.

LM from Texas Instruments

That’s one of the reasons that the higher voltage ICs LM and LM have a higher gain than the LM – it’s simply to ensure full output swing before the input stage causes distortion. It should be easy enough to fabricate a suitable heatsink if datasheeg have some sheet copper available. It would be worthwhile to give it a very light spray with matte black paint to improve radiation. If you do datasheer C1, you will almost certainly hear some ‘scratching’ noises from the pot as it’s rotated because there’s a small DC offset at the inputs.

These range from a Wien bridge oscillator to intercoms and various others.

The IC is useful for headphones, intercoms, portable radios etc. Two are needed, one for each side of the IC. It usually won’t need to be anything special, but it will usually have to be cheap and easy to build. You can use either input for the signal, and simply ground the unused input. The only thing that lm348n approaches being critical is the bypass cap.

LM386, LM380 & LM384 Power Amplifiers

All pin numbers refer to the pin LM and the LM Production processing does not necessarily include testing of all parameters. The bypass cap C2 is optional as well, but if you don’t dxtasheet it the power supply rejection is rather poor, so anything other than a battery supply may cause some hum. The LM is also available in a pin package, which has greater dissipation and can provide more power.


In order to hold system cost to a.

HTTP This page has been moved

None are anything special, and they are fairly low power the LM datasheeg only rated for mW into 8 ohms. The output automatically self-centers to one-half the supply voltage. Reproduction or re-publication by any means whatsoever, whether electronic, mechanical or electro-mechanical, is strictly prohibited under International Copyright laws.

The suggested heatsink designs are shown below. Uses include simple phonograph amplifiers, intercoms, line drivers, teaching machine outputs, alarms, ultrasonic drivers, TV sound systems, AM-FM radio and sound projector systems. Of the three types, the LM is the more popular. A copper lead frame is used with the center three.

5-W Audio Power Amplifier

It’s theoretically possible if you use a high supply voltage and a 16 or 32 ohm load, but that’s not recommended because device dissipation will be well in excess of that which the device can handle safely.

The 8-pin version is shown first. The output is short-circuit proof with internal thermal. Quiescent Output Voltage is at One Half of the.

Maximum output power into an 8 ohm load is around mW dstasheet acceptable distortion.

In order to hold system cost to a minimum, gain is internally fixed at 34 dB. The Zobel network at the output is needed to ensure stability when leads are attached, but even if the speaker is only a few millimetres away, don’t leave it out or the amp may oscillate.

C5 is a supply bypass cap, and it should be as close to the supply pins as possible. I don’t think I even need to say that this IC isn’t suitable for a subwoofer. Input stage distortion will not occur until the input signal peak exceeds mV or so, and that’s far more than necessary given the gain of the IC.

That means that the maximum input voltage will be around mV RMS sinewave at the onset of clipping. The circuit is shown for reference only, and is adapted lm384m the datasheet but has been redrawn. The quiescent output voltage is set internally to be half the supply voltage, and by default the gain is 20 26dB. Every so often, you’ll lm34n a need for a low power amplifier.

  ASTM A967-05 PDF

The datasheets don’t mention it, but there’s every chance that the ICs will oscillate if you fail to bypass the supply. All trademarks are the property of their respective owners.

The output automatically self-centers to one-half the. The circuit shown is only partially optimised for best performance.

Production processing does not. LM or LM can use a supply voltage of 10V up to 22V or 26V respectively, but don’t even think about it if you don’t include heatsinks. These are allegedly available, but I couldn’t find anything even remotely similar from my normal suppliers. The negative input signal doesn’t get cut off as you might expect, because the emitter is still positive. The author Rod Elliott grants the reader the right to use this information for personal use only, and further allows that one 1 copy may be made for reference while constructing the project.

The output is short-circuit proof with internal thermal limiting.

I’ve shown the LM with the same component values as the LM, and performance will be similar, but you can get higher power. They can be run without a heatsink, but only for low power output, and care is needed to ensure the IC doesn’t overheat. It is possible to use a ground-plane on a PCB as a heatsink, but it’s not very effective and you need a lot of area to get what is still a sub-standard heatsink. Products conform to specifications per the terms of the Texas Instruments standard warranty.

See SNAA for circuit details. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of.