ISO 14998 PDF

Published by on December 23, 2019
Categories: Software

Industries du pétrole et du gaz natruel — Équipement de fond de trou — Accessoires de complétion. STANDARD. ISO. First edition. Products covered under ISO , ISO , ISO , ISO , ISO , ISO , ISO ‑2, ISO , and ISO ‑1 are not included. STANDARD. ISO. First edition. Reference number. ISO (E). This is a free 6 page sample. Access the full version online.

Author: Mikajin Akinolabar
Country: Greece
Language: English (Spanish)
Genre: Music
Published (Last): 19 September 2006
Pages: 353
PDF File Size: 8.91 Mb
ePub File Size: 14.85 Mb
ISBN: 695-9-19490-653-5
Downloads: 58362
Price: Free* [*Free Regsitration Required]
Uploader: Akirg

Personnel performing visual examinations shall have lso annual eye examination in accordance with an international or national standard such as ISOas applicable to the discipline to be performed. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.

Quality control documentation includes all documents and data necessary to demonstrate conformance to 7. For example, various shear device options can be displayed, as shown in Figure 2. Read more about subscriptions.

The sealing devices shall be completely covered by liquid prior to start of the unloading test. This service is not available if you are a URL user where you do not log in with an email address. ISO CD b heat treatment conditions; c mechanical-property limits: End connections are specifically excluded from this requirement.

For iiso references, iao latest edition of the referenced document including any amendments applies. You can publish your book online for free in a few minutes! The validation grades are summarized in Table 1.

Rives Basane – | Antalis

The hardness results shall verify through documented correlation that the mechanical properties of the material tested meet the properties specified. This International Standard 114998 intended to give requirements kso information to both parties in the selection, manufacture, testing and use of completion accessories. A pressure hold is required at the low 19498 of the temperature cycle range and after heating back up to the maximum rated temperature.

  2008 ACURA MDX MANUAL PDF

Documents and data may be in any form of type of media, such as hard copy or electronic media. Annex B-D testing shall follow after Annex A testing and can be included in a single test procedure if applicable. Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation.

ISO in English | Download PDF |

The words you are searching are inside this book. This control shall provide for identification, documentation, evaluation, segregation when applicableand disposition of non-conforming assemblies or components.

To get more targeted content, please make full-text search by clicking here. This may be done by testing only the component or series of components, rather than iiso entire assembly.

Drift bar dimensions shall meet the requirements specified in ISO Design changes identified as non-substantive shall include documented justification. This International Standard provides seven standard design validation grades V6 to V0as defined in 6.

Quality grade Oso provides additional inspection and verification steps, and quality 149998 Q1 is the highest grade provided. A web subscription provides an easy and secure access to standards, and you are guaranteed to always have the latest edition. Completion accessories shall not be rated for any of the functionalities covered by Annexes B-D without meeting the validation test requirements of the appropriate Annex for the same validation grade as the Annex A testing.

Drill stem design and operating limits [10] ISOPetroleum and natural gas industries — Drilling and production equipment – Rotary drilling equipment – Part 2: Start Webshop Product catalog Product presentation. Metal mechanical properties over the temperature range shall be considered when determining performance ratings.

  APOSTILA ARQUIVOLOGIA VESTCON PDF

ISO 14998:2013

The benefits of a subscription: Quality grade Q3 is the minimum grade of quality offered by this product standard.

These requirements and operating conditions may be conveyed by means of a dimensional drawing, data sheet or other suitable documentation.

ISO CD 5. Products shall be supplied to at least the quality control grade specified. The main task of technical committees is to prepare International Standards.

МКС EN ISO 14998:2014

For completion accessories validated to grades V4 thru V0, a rated performance envelope is required. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

Use a gas test medium of air, nitrogen, or other gases or mixtures of gases.

If the completion accessory is also rated for any of the other functionalities listed in Table 1, then the requirements of these annexes shall also be met for the same validation grade as the Annex A testing.

Evaluation results shall be approved by qualified person other than the person performing them and records of the results shall become a portion of the design documentation. Hardness testing is the only mechanical-property test required after stress relieving.

This ensures that you are always up-to-date and saves you both time and money.