FBI XL2T PROGRAM PDF

Published by on May 28, 2020
Categories: Music

Introduction The XL-2T is a state of the art microprocessor-based control/ communicator. The system features seven (7) fully programmable zones. Programming. XL-2T. Security System. Installation and Setup Guide. STAY. INSTANT. ACYLB. READY APPENDIX D – SYSTEM PROGRAMMING WORKSHEET. Example: To program phone number enter 1#8#0#0# etc. Exit Program STAY. Default Panel Short “EEPROM RESET” pins on panel and power up system.

Author: Mikaramar Samutilar
Country: Serbia
Language: English (Spanish)
Genre: History
Published (Last): 12 March 2017
Pages: 478
PDF File Size: 7.29 Mb
ePub File Size: 6.44 Mb
ISBN: 508-8-44057-740-2
Downloads: 72640
Price: Free* [*Free Regsitration Required]
Uploader: Faujinn

Each condition will cause these LEDs to operate differently as follows: Separate the two halves of the keypad by placing a straight-slot screwdriver into one of the two slots at the bottom of the keypad and twisting. Section 6 – System Programming When programming the English zone descriptors, use the following techniques to program the characters: Question 10, L1 – Burglary Bell Time-out On LED keypads the sounder will beep after each entry.

Question 11, L1 fni Exit Delay Enter the digit from the table below. LCD display keypads will indicate the following message: For a period of 5 seconds the fire zone will not be scanned allowing the smoke detectors to settle. I want proyram change this 3 digit code to a new 4 digit code, but with no success.

I then pressed code button followed by master codethen user no 3 and then new 4 digit user code. The system contains up to fifteen user codes 4 digits each with the following applications: Once deleted their values will be null. Sounder Only always enabled Programmable Dialer Attempts: Page of 93 Go. Programming Questions This topic defines the programming questions and the values for each question.

  CALCUL DES FONDATIONS SUPERFICIELLES ET PROFONDES ROGER FRANK PDF

Replacement microprocessors are available through Technical Support or Customer Service. Programming can be performed through any progra, the compatible keypads or the system can be uploaded and downloaded remotely using the EZ-Mate PC Downloader Software. To select a trigger type enter the 2 digits in either L1 L2 or L3 L4 desired trigger type for each output trigger. With this device some systems can obtain dial tone in areas which do not automatically provide dial tone.

FBI XL-2T Turbo Program Sheet

System ready to be armed System not ready to be armed To print the manual completely, please, download it. Create an opening and mount a standard double-gang box. Enter text from picture: By pressing ‘print’ button you will print only current page. Some new features have been added and others have been modified. The door of the metal cabinet may be removed to make it easier to install the control panel. Page 23 Fire Trouble is reported to the CS dbi enabled program question 32, location 3.

Section 5 – System Operations Keypad Sounder The sounder or loudspeaker housed inside the keypad, emits annunciates sounds according to the condition of the security system. Page 70 Section 6 – System Programming When programming the English zone descriptors, use the following techniques to program the characters: The following is a quick comparison.

  ARTICULOS COXARTROSIS PDF

FBI XL-2T PC download software

The rear plastic mounting plate is not used for recessed installations. Question 32, L1 – Bypass Code Good Day I had a four digit user code, but the fib digit was lost.

Upon entry to the system log view, LCD based keypads will show the events one at progrzm time starting from the oldest event. There are 36 total questions, with multiple data entry locations.

FBII XL-2T Installation And Setup Manual

Proceed to question 02 through the sequence Refer to the Installation Instructions for hookup information. The purpose of this manual is to give you a brief overview of the XL-2T control panel, and provide instructions for installing a basic system. After this time period, power is restored.

Upon detection of the first violation, smoke detector power on conventional 4 wire smoke detectors connected to ZONE modules will be reset for a period of 8 seconds. If selected, then a negative acknowledgment 4 short beeps will be heard after attempting to enter this mode.

I shall be pleased to learn from you in this regard. Comments to this Manuals Your Name. It is time to change code for security reasons.

The system features seven 7 fully programmable zones. Directly to a control panel having a keypad cutout on the front of its enclosure.