Published by on December 25, 2019
Categories: Music

eh11a regulator datasheet, cross reference, circuit and application notes in pdf EH11A SOT eh14a regulator eh16a regulator voltage regulator sot Cheap Voltage Regulators/Stabilizers, Buy Directly from China Suppliers:EH11A H11A AZH-ADJ Enjoy ✓Free Shipping Worldwide! ✓Limited Time Sale. Cheap spot cartoon, Buy Quality regulator filter directly from China spot batteries Suppliers: EH11A AZH – ADJTRE1 adjustable power supply voltage.

Author: Tektilar Durisar
Country: Uzbekistan
Language: English (Spanish)
Genre: Music
Published (Last): 27 September 2010
Pages: 467
PDF File Size: 12.30 Mb
ePub File Size: 10.1 Mb
ISBN: 966-3-45426-887-9
Downloads: 55812
Price: Free* [*Free Regsitration Required]
Uploader: Dugami

Below is the pinout of the LM voltage voltagw To measure the output voltage, we place the same multimeter set in the DC voltage setting and now place the positive probe of the multimeter on the output pin of the regulator and the negative probe on the ground pin of the regulator.

The regularor that we should read should be higher than the voltage the regulator is rated to output. Rgulator input voltage that needs to be regulated down goes into pin 1 Input.

We take the probes of the multimeter and place the positive probe normally the red probe on the input pin of the voltage regulator and the negative probe normally black probe on the ground pin. All a user must do is calculate the output that the regulator should output and perform the same test as is shown above to see whether it is good or defective.

HomeMade DIY HowTo Make: Advanced Analog Circuit EH11A J01 1A LOW DROPOUT LINEAR REGULATOR

Measuring the Output Voltage Now that this step is complete, we now read the output voltage. Before we get into vpltage to read the voltages with a multimeter, first we’ll go over the pinout of a voltage regulator, so that you’ll know which pins to read voltages from.


We should now read a voltage at or about the rated voltage that the regulator is designed for.

Unlike fixed voltage regulators, adjustable regulators can be regulated to output adjustable voltages. The DC voltage setting is the setting of the multimeter that has the following symbol or sign. If the regulator is rated to output 5 volts, then we should read voltafe voltage very near 5 volts coming out from its output.

eh11a regulator datasheet & applicatoin notes – Datasheet Archive

The LM is a voltage regulator is rated to output 5 volts, so we should read reghlator output. An adjustable regulator can be tested in the same way. We check the voltage input into the voltage regulator and the voltage output from the regulator.

If we read at the input pin the voltage which we feed into the regulator and read at the output pin the output voltage which the regulator is rated for, then we know that the voltage regulator is good.

If we don’t read the correct voltages, then more than likely it is a defective regulator.

This is why we do this test. How To Test a Voltage Regulator A voltage regulator is a device that takes in an input voltage and regulates it down to the voltage that it is rated for.

Being that a voltage regulator passes out a regulated output voltage, the only test we must do to check a voltage regulator is a voltage test. If we read a higher voltage, then the voltage regulator is receiving sufficient voltage to regulate down.


The ground pin is pin 2. To test the voltage going into the voltage regulator, we take a multimeter and place it in the DC voltage en11a.

EH11A AZ1117H – ADJTRE1 adjustable power supply voltage regulator original spot

If we do not, then the voltage regulator is defective, as it does not do the job it was designed for, which is output a regulated voltage. If the multimeter does read a voltage near its rated output voltage, the voltage regulator is functional and is good.

So we’ll now go through specifically how to test a voltage regulator. This is normally volts higher. A voltage regulator is a device that takes in an input voltage and regulates it down to the voltage that it is rated for. This is to make sure that voltage is, in regluator, being supplied to the regulator.

As an example, we’ll use the popular voltage regulator, the LM And the regulated output voltage comes out from pin 3 Output. Measuring the Input Voltage When testing the voltage of a voltage regulator, we first check the voltage from the input pin to ground. If the regulator isn’t receiving sufficient voltage, of course it will not be able to output its rated regulated voltage.