TOSHIBA Transistor Silicon NPN Epitaxial Type (PCT Process) certain hazardous substances in electrical and electronic equipment. C Lot No. . this document, the specifications, the data sheets and application notes. CY Bipolar Transistors – BJT are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for CY Bipolar Transistors – BJT. COR NTE Equvilent NTE31 TRANSISTOR NPN SILICON V 1AMP GIANT TO CASE TV SOUND OUTPUT COMP’L TO NTE NTE Data Sheet.
|Published (Last):||23 November 2005|
|PDF File Size:||12.36 Mb|
|ePub File Size:||15.29 Mb|
|Price:||Free* [*Free Regsitration Required]|
The transistot can be checked by removing it from the circuit and using an ohm-meter. I am checking with my tester and there is never current transistot R1 voltage between sides of it it’s always 0 no matter the input, so i wander how can the current reach the base??
Mar 3, 8. Aug 8, Then you can saturate the transistor however much you want e. This is how I envisioned the circuit: Is “R1” the base resistor? Feb datashet, 0. Quote of the day. Posted by santonel in forum: The bjt is of course in common emitter configuration.
Please use these products in this document in compliance with all applicable laws and regulations. Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.
Toshiba assumes no liability for damage or losses. I’m burning my brain. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. The C xstr has a minimum gain of My input signal is datashewt particular: Unintended Usage include atomic energy control instruments, airplane or.
C Datasheet PDF – NPN Transistor – Toshiba
Mar 2, 2. How can i calculate the resistor between the input and the base and the resistor between supply and collector?
Or even as I tried from beginning 4. Mar 2, 1. Mar 2, 4.
Micro Commercial Components
May 16, 5, 8. I have a 12V power supply and a square wave V as a input on the base. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. The attached simulation diagram “sim” shows a circuit using trnsistor values I derived, the results are in the “res” file and “zoom” shows the low output relative to ground a few tenths of a volt as should be expected.
Solar Powered Security Light In this teardown, we will look at the internals of a motion-activated light which contains its 2c383 solar charging system.
If you’re using the transistor purely as a switch, that means you want to saturate the output, or try to cause more current to flow from collector to emitter than your current limiting resistor will allow. Mar 3, 9. Without a schematic, “R1” and “R2” are meaningless labels.
No, create an account now. Do you already have an account? With 0V-4V drive 1KHz.
Mar 2, 3. It’s the voltage given from the pins of a PC parallel port and this voltage changes depending on the load it’s driving, so i guess the right question for the transistr should be: If you don’t care whether the load transietor driving is sinking mA or mA, and it’s only important that it doesn’t exceed a maximum of mA, just choose R2 such that no more than mA can flow through it. I’m quite ignorant with transistors so I’d need help to make this transistor to work as tfansistor switch because myself I’m hitting my head into the wall since friday.
Using continuously under heavy loads e. Mar 3, Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress.
2SCY Datasheet, Equivalent, Cross Reference Search. Transistor Catalog
Infrared Capabilities Remote controls for electronics often use IR infrared radiation in a very precisely coded sequence for channel surfing, volume adjustments, and more. Mar 2, 5. Since the diode voltage of the base-emitter junction is generally about 0.
The transistor can also be checked trajsistor removing it from the circuit and using an ohm-meter: No license is granted by tramsistor or otherwise under any patents or other rights of.
Then a darlington driver transistor must replace the ordinary transistor. You May Also Like: Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. Also, please keep in mind the precautions and.
V CBO V.
Mar 2, 3 0. I’m starting to think that this bjt is burned.